DodgeForum.com
Driver side brake lines with the combo valve. I like it
Driver side brake lines with the combo valve. I like it
0 2020/06/12 17:18:07
The location is different than the factory. I never liked the factory position.
The location is different than the factory. I never liked the factory position.
0 2020/06/13 12:31:59
Plenty of clearance. I should be able to hide it with the fender wells.
Plenty of clearance. I should be able to hide it with the fender wells.
0 2020/06/13 12:32:43
The rods. Short is modified, long is factory.
The rods. Short is modified, long is factory.
0 2020/06/13 12:33:19
Final location. I have to add some bolts, a support and paint, but this is where its going.
Final location. I have to add some bolts, a support and paint, but this is where its going.
0 2020/06/13 12:33:52
0 2020/06/19 17:15:00
0 2020/06/19 17:15:17
0 2020/06/19 17:15:28
0 2020/06/19 17:15:37
Showing the inside. I got good penetration on the welds. It should hold up well.
Showing the inside. I got good penetration on the welds. It should hold up well.
0 2020/06/27 14:16:05
After cleanup. Ill still have some work to do, but it looks good to me.
After cleanup. Ill still have some work to do, but it looks good to me.
0 2020/06/27 14:17:01
Installed. Its only clamped on the inside edge. Ill add some tabs on the bottom too. Fits nice.
Installed. Its only clamped on the inside edge. Ill add some tabs on the bottom too. Fits nice.
0 2020/06/27 14:17:35
Very poorly done radio hole
Very poorly done radio hole
0 2020/08/08 11:41:11
patch panel fitted and tacked
patch panel fitted and tacked
0 2020/08/08 11:41:35
getting there.
getting there.
0 2020/08/08 11:41:57
Not done, but done for now. Ill have to take it too work.
Not done, but done for now. Ill have to take it too work.
0 2020/08/08 11:42:17
Passenger side header shot. Ignore the brake line, Im not done yet.
Passenger side header shot. Ignore the brake line, Im not done yet.
0 2020/10/10 11:10:07
Driver side shot. Its tight with the starter and the steering in place. I know it looks like a bad transition on the exhaust, but its not. Thats a slip fit junction that Im welding up.
Driver side shot. Its tight with the starter and the steering in place. I know it looks like a bad transition on the exhaust, but its not. Thats a slip fit junction that Im welding up.
0 2020/10/10 11:10:52
Exhaust tucked in nicely. The cross members are the lowest part of the truck.
Exhaust tucked in nicely. The cross members are the lowest part of the truck.
0 2020/10/10 11:12:21
0 2020/10/17 14:20:24
0 2020/10/17 14:20:35
0 2020/10/17 14:20:44
0 2020/10/17 14:20:53
A few bad spots. Not bad overall. I was not trying to close the ends until later. This is MIG
A few bad spots. Not bad overall. I was not trying to close the ends until later. This is MIG
0 2020/10/24 11:42:48
I got better as I went. This is also MIG.
I got better as I went. This is also MIG.
0 2020/10/24 11:42:56
TIG. Just ugly. Dont even ask about the backside of the angle.
TIG. Just ugly. Dont even ask about the backside of the angle.
0 2020/10/24 11:43:04
Rough bed mounts. I cleaned and cut them before installation.
Rough bed mounts. I cleaned and cut them before installation.
0 2020/11/07 16:57:24
Bed coming off again.
Bed coming off again.
0 2020/11/07 16:57:57
Its getting easier. I got it this far by myself.
Its getting easier. I got it this far by myself.
0 2020/11/07 16:58:23
Mounts and rear crossmember are new additions
Mounts and rear crossmember are new additions
0 2020/11/07 16:58:53
Another shot. Still a lot of work to do.
Another shot. Still a lot of work to do.
0 2020/11/07 16:59:32
The welds are solid, because I ground a few out. They are penetrating good, but they look like catapillers for some reason.
The welds are solid, because I ground a few out. They are penetrating good, but they look like catapillers for some reason.
0 2020/11/07 16:59:57
They were penetrating, but not very good
They were penetrating, but not very good
0 2020/11/15 05:36:35
Better. A little fat, but they are not going to fail.
Better. A little fat, but they are not going to fail.
0 2020/11/15 05:37:02
0 2020/11/15 05:37:33
Rearend out for final welding
Rearend out for final welding
0 2020/11/15 05:38:24
4-link brackets finally all welded up. Just need some paint.
4-link brackets finally all welded up. Just need some paint.
0 2020/11/15 05:38:44
All done, and back in place. This is fully compressed and touching the frame. It will never get this high.
All done, and back in place. This is fully compressed and touching the frame. It will never get this high.
0 2020/11/15 05:39:18
Horrible picture, but if you look close, you can see I added two vertical supports in the middle.
Horrible picture, but if you look close, you can see I added two vertical supports in the middle.
0 2020/11/25 13:01:59
I tied it into the crossmember at the shocks. It should be nice and sturdy.
I tied it into the crossmember at the shocks. It should be nice and sturdy.
0 2020/11/25 13:03:01