DodgeForum.com
Upper A-arm. Ill add a gusset at the ball joint.
Upper A-arm. Ill add a gusset at the ball joint.
0 2021/12/27 16:06:42
One of the pass throughs. Itll look better when Im done.
One of the pass throughs. Itll look better when Im done.
0 2021/12/18 14:01:08
Jack point.tow hitch mount. Ill seam seal this also. I can bolt on the hitch if I need it.
Jack point.tow hitch mount. Ill seam seal this also. I can bolt on the hitch if I need it.
0 2021/12/18 14:00:08
Bigger beefier forged bar ends for the a-arms. Ill start on these hopefully early next year.
Bigger beefier forged bar ends for the a-arms. Ill start on these hopefully early next year.
0 2021/12/18 13:59:19
22 gallon tank from a 70 mustang. I didnt like the idea of a 15 or 16 gallon tank. I dont know what the gas mileage is on a carbureted 318, but Im sure it sucks.
22 gallon tank from a 70 mustang. I didnt like the idea of a 15 or 16 gallon tank. I dont know what the gas mileage is on a carbureted 318, but Im sure it sucks.
0 2021/12/18 13:57:20
Flipped and ready to make a mess. Ill show more details when its painted.
Flipped and ready to make a mess. Ill show more details when its painted.
0 2021/12/05 10:39:19
Flipping the frame over was a bit sketchy. I got it though.
Flipping the frame over was a bit sketchy. I got it though.
0 2021/12/05 10:38:29
Front side of the driver side rear pass through. This will be under the bed on the drivers side.
Front side of the driver side rear pass through. This will be under the bed on the drivers side.
0 2021/11/20 16:08:57
This is the back side of the drivers side pass through. Its under the drivers feet.
This is the back side of the drivers side pass through. Its under the drivers feet.
0 2021/11/20 16:08:11
Grind away.
Grind away.
0 2021/11/20 16:07:48
Weld it up....
Weld it up....
0 2021/11/20 16:07:30
Small plug from 3/16" plate
Small plug from 3/16" plate
0 2021/11/20 16:07:06
Big hole for the steering box, I think
Big hole for the steering box, I think
0 2021/11/20 16:06:34
Last pass of the day. I went from right to left, so it started out pretty good, then got ugly at the end.
Last pass of the day. I went from right to left, so it started out pretty good, then got ugly at the end.
0 2021/11/13 16:49:57
Practicing TIG. At least Im not dipping the tungsten every three seconds now.
Practicing TIG. At least Im not dipping the tungsten every three seconds now.
0 2021/11/13 16:48:57
I like it, but it wont stay. Ill make another one that will be removable.
I like it, but it wont stay. Ill make another one that will be removable.
0 2021/11/13 16:48:16
Shock mount hoop. The shock is fully extended here, so the bolt hole will be about 2-1/2" lower.
Shock mount hoop. The shock is fully extended here, so the bolt hole will be about 2-1/2" lower.
0 2021/11/13 16:47:01
Side profile. They match pretty good I think.
Side profile. They match pretty good I think.
0 2021/11/06 14:50:02
Everything is nice and level. Except the bumper apparently.
Everything is nice and level. Except the bumper apparently.
0 2021/11/06 14:49:29
Drivers side.
Drivers side.
0 2021/11/06 14:49:12
Passenger side.
Passenger side.
0 2021/11/06 14:48:53
These are the SPC uppers. I can buy all the parts and make them.
These are the SPC uppers. I can buy all the parts and make them.
0 2021/11/06 14:48:14
Front side of the same one. Again, itll all be welded and smoothed.
Front side of the same one. Again, itll all be welded and smoothed.
0 2021/11/04 17:24:21
Back side of the pass through. It will get welded and smoothed.
Back side of the pass through. It will get welded and smoothed.
0 2021/11/04 17:23:51
We accidentally cut this before and left it for later. Well, its later.
We accidentally cut this before and left it for later. Well, its later.
0 2021/11/04 17:23:12
Bad picture, but it shows the anti-dive angle. I just have to make the other side match perfectly.
Bad picture, but it shows the anti-dive angle. I just have to make the other side match perfectly.
0 2021/11/04 17:22:23
Everything is straight and level. This side went okay. I can still hear the other side laughing at me.
Everything is straight and level. This side went okay. I can still hear the other side laughing at me.
0 2021/11/04 17:21:35
It would replace this weird shaped cross member. And I would add a top part also, to close it up.
It would replace this weird shaped cross member. And I would add a top part also, to close it up.
0 2021/10/29 15:18:02
Fits pretty good I think.
Fits pretty good I think.
0 2021/10/29 15:17:37
This was notched with a grinder, so it isnt perfect.
This was notched with a grinder, so it isnt perfect.
0 2021/10/29 15:17:05
Top control arm bars removed and cleaned up
Top control arm bars removed and cleaned up
0 2021/10/29 15:16:35
Top mounts cut flush and ready for mods
Top mounts cut flush and ready for mods
0 2021/10/29 15:16:05
Passenger side. Should also be 5 degrees, but it should at least match.
Passenger side. Should also be 5 degrees, but it should at least match.
0 2021/10/23 15:51:48
Drivers side. Should be around 5 degrees.
Drivers side. Should be around 5 degrees.
0 2021/10/23 15:51:19
The upright needs to be straight also. I drew in where the "top hat" and the lower cross member meet. There is a seem here that gets welded.
The upright needs to be straight also. I drew in where the "top hat" and the lower cross member meet. There is a seem here that gets welded.
0 2021/10/23 15:50:23
Both cross member uprights are level and within .2 degrees of each other.
Both cross member uprights are level and within .2 degrees of each other.
0 2021/10/23 15:49:42
Started out too fast at the top, but managed to slow down and make a good weld by the bottom.
Started out too fast at the top, but managed to slow down and make a good weld by the bottom.
0 2021/10/23 15:49:00
Finished engine stand, sitting on a furniture dolly.
Finished engine stand, sitting on a furniture dolly.
0 2021/10/23 15:48:26
The helix/uncle jimmys IFS. Its about to be removed or seriously modified. I have to take measurements first.
The helix/uncle jimmys IFS. Its about to be removed or seriously modified. I have to take measurements first.
0 2021/10/22 15:23:04
Ride height. I still had 5-1/2" at the lowest point of the frame. Thats more than my Charger has.
Ride height. I still had 5-1/2" at the lowest point of the frame. Thats more than my Charger has.
0 2021/10/22 15:22:17