DodgeForum.com
0 2020/11/15 05:37:33
Better. A little fat, but they are not going to fail.
Better. A little fat, but they are not going to fail.
0 2020/11/15 05:37:02
They were penetrating, but not very good
They were penetrating, but not very good
0 2020/11/15 05:36:35
The welds are solid, because I ground a few out. They are penetrating good, but they look like catapillers for some reason.
The welds are solid, because I ground a few out. They are penetrating good, but they look like catapillers for some reason.
0 2020/11/07 16:59:57
Another shot. Still a lot of work to do.
Another shot. Still a lot of work to do.
0 2020/11/07 16:59:32
Mounts and rear crossmember are new additions
Mounts and rear crossmember are new additions
0 2020/11/07 16:58:53
Its getting easier. I got it this far by myself.
Its getting easier. I got it this far by myself.
0 2020/11/07 16:58:23
Bed coming off again.
Bed coming off again.
0 2020/11/07 16:57:57
Rough bed mounts. I cleaned and cut them before installation.
Rough bed mounts. I cleaned and cut them before installation.
0 2020/11/07 16:57:24
TIG. Just ugly. Dont even ask about the backside of the angle.
TIG. Just ugly. Dont even ask about the backside of the angle.
0 2020/10/24 11:43:04
I got better as I went. This is also MIG.
I got better as I went. This is also MIG.
0 2020/10/24 11:42:56
A few bad spots. Not bad overall. I was not trying to close the ends until later. This is MIG
A few bad spots. Not bad overall. I was not trying to close the ends until later. This is MIG
0 2020/10/24 11:42:48
0 2020/10/17 14:20:53
0 2020/10/17 14:20:44
0 2020/10/17 14:20:35
0 2020/10/17 14:20:24
Exhaust tucked in nicely. The cross members are the lowest part of the truck.
Exhaust tucked in nicely. The cross members are the lowest part of the truck.
0 2020/10/10 11:12:21
Driver side shot. Its tight with the starter and the steering in place. I know it looks like a bad transition on the exhaust, but its not. Thats a slip fit junction that Im welding up.
Driver side shot. Its tight with the starter and the steering in place. I know it looks like a bad transition on the exhaust, but its not. Thats a slip fit junction that Im welding up.
0 2020/10/10 11:10:52
Passenger side header shot. Ignore the brake line, Im not done yet.
Passenger side header shot. Ignore the brake line, Im not done yet.
0 2020/10/10 11:10:07
Not done, but done for now. Ill have to take it too work.
Not done, but done for now. Ill have to take it too work.
0 2020/08/08 11:42:17
getting there.
getting there.
0 2020/08/08 11:41:57
patch panel fitted and tacked
patch panel fitted and tacked
0 2020/08/08 11:41:35
Very poorly done radio hole
Very poorly done radio hole
0 2020/08/08 11:41:11
Installed. Its only clamped on the inside edge. Ill add some tabs on the bottom too. Fits nice.
Installed. Its only clamped on the inside edge. Ill add some tabs on the bottom too. Fits nice.
0 2020/06/27 14:17:35
After cleanup. Ill still have some work to do, but it looks good to me.
After cleanup. Ill still have some work to do, but it looks good to me.
0 2020/06/27 14:17:01
Showing the inside. I got good penetration on the welds. It should hold up well.
Showing the inside. I got good penetration on the welds. It should hold up well.
0 2020/06/27 14:16:05
0 2020/06/19 17:15:37
0 2020/06/19 17:15:28
0 2020/06/19 17:15:17
0 2020/06/19 17:15:00
Final location. I have to add some bolts, a support and paint, but this is where its going.
Final location. I have to add some bolts, a support and paint, but this is where its going.
0 2020/06/13 12:33:52
The rods. Short is modified, long is factory.
The rods. Short is modified, long is factory.
0 2020/06/13 12:33:19
Plenty of clearance. I should be able to hide it with the fender wells.
Plenty of clearance. I should be able to hide it with the fender wells.
0 2020/06/13 12:32:43
The location is different than the factory. I never liked the factory position.
The location is different than the factory. I never liked the factory position.
0 2020/06/13 12:31:59
Driver side brake lines with the combo valve. I like it
Driver side brake lines with the combo valve. I like it
0 2020/06/12 17:18:07
Fuel log. Its a -8 from the floor bulkhead to the log, then a -6. I dont need two -6 outlets, but who knows.
Fuel log. Its a -8 from the floor bulkhead to the log, then a -6. I dont need two -6 outlets, but who knows.
0 2020/06/12 17:17:02
The clutch line. It will get a flex line between the hard line and the slave cylinder
The clutch line. It will get a flex line between the hard line and the slave cylinder
0 2020/06/12 17:16:13
Brake and clutch lines. I like them straight and clean. The wires will be run along the fender. I might try and run them under.
Brake and clutch lines. I like them straight and clean. The wires will be run along the fender. I might try and run them under.
0 2020/06/12 17:14:44
Here you can see the spacers. Also the upper rear shock mounts are temporarily tacked in. Ill finish all this soon.
Here you can see the spacers. Also the upper rear shock mounts are temporarily tacked in. Ill finish all this soon.
0 2020/05/24 05:28:43
Back inside and on the stands.
Back inside and on the stands.
0 2020/05/24 05:28:21