96 dodge ram 2500 v-10 4x4 AT w/ OD 214,000 original miles
#241
#242
Here at the shop now. Had one last question? Does anyone know if the green and red ground wire on the coil packs hooks to the valve cover or the upper plenum? About the only wire that looks like it could go either place? Can't remember which bolt I loosened to remove it?
#244
#246
Kinda how life has been going the last year or so! My lady of seven years hit menopause. Blamed it on me and gave me the boot! I built her a house and paid for her cancer medicine and all her bills while she fought the battle. She survived and this is the thanks I get! Been a downhill slide since!
Life, I suppose? Nobody said it would be easy. Just have to figure out my next move?
Life, I suppose? Nobody said it would be easy. Just have to figure out my next move?
#248
Pulled the plugs. Going to get WD40 to hose the cylinders down and then leave it alone for a bit. Gotta process thru this and figure out my next move? Run n out of time to waste on this rig! I have a 102 year old boat that is reason my truck is dead! Spent so much time on the boat. I neglected the truck! But, this will be the fifth engine I've killed! Get n pretty good at it! Don't even have to try and they die! Is what it is! Crying over spilled milk ain't my style! Pick myself up. Brush off the dirt and go do something else! I have a Detroit diesel to go work on now! At least it runs!! It used to anyways. Before I started work n on it? If it don't start. I'm walking away from everything and relocated! F*#k it!
#249
Bad intake manifold?
So how does an engine fill up with water if you know the gaskets are good? Seems to me, it would have to be flowing thru the intake manifold?
After all, the intake is the weak link being that it's aluminium! That will give way under extreme heat before the cast iron heads and block, correct? Maybe? Reaching now. But my diesel mechanic said if all the cylinders are full. It's coming from the top of the engine. He also said if the cylinders were full when I tried to start it I would've bent some push rods? I had all the push rods out. Never rolled any of them on the table to see if they were bent? I've seen bent push rods! These looked nothing like the bent ones I've seen?
Saw an intake manifold for less then $100 on eBay!
After all, the intake is the weak link being that it's aluminium! That will give way under extreme heat before the cast iron heads and block, correct? Maybe? Reaching now. But my diesel mechanic said if all the cylinders are full. It's coming from the top of the engine. He also said if the cylinders were full when I tried to start it I would've bent some push rods? I had all the push rods out. Never rolled any of them on the table to see if they were bent? I've seen bent push rods! These looked nothing like the bent ones I've seen?
Saw an intake manifold for less then $100 on eBay!
Last edited by Stitch Mitchell; 02-18-2020 at 12:32 AM.
#250
So how does an engine fill up with water if you know the gaskets are good? Seems to me, it would have to be flowing thru the intake manifold?
After all, the intake is the weak link being that it's aluminium! That will give way under extreme heat before the cast iron heads and block, correct? Maybe? Reaching now. But my diesel mechanic said if all the cylinders are full. It's coming from the top of the engine. He also said if the cylinders were full when I tried to start it I would've bent some push rods? I had all the push rods out. Never rolled any of them on the table to see if they were bent? I've seen bent push rods! These looked nothing like the bent ones I've seen?
Saw an intake manifold for less then $100 on eBay!
After all, the intake is the weak link being that it's aluminium! That will give way under extreme heat before the cast iron heads and block, correct? Maybe? Reaching now. But my diesel mechanic said if all the cylinders are full. It's coming from the top of the engine. He also said if the cylinders were full when I tried to start it I would've bent some push rods? I had all the push rods out. Never rolled any of them on the table to see if they were bent? I've seen bent push rods! These looked nothing like the bent ones I've seen?
Saw an intake manifold for less then $100 on eBay!